Exactly How To Install A Bath Tub (For Novices).
Exactly How To Install A Bath Tub (For Novices).
Blog Article
Are you currently interested in information about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately difficult job. If the old tub is easily available, the project can relocate rapidly; if you have to open a wall surface to eliminate the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub and also set in the new one. Make sure you have actually certified yourself for the job and also fit trying it. Instead of working with a specialist to take over a halfway-completed task, it is far better to consider employing one prior to you begin. Chances are you might need an expert plumber to make tube connections.
This article will certainly aid you set up a brand-new bathtub in your shower room if you have actually currently bought a new tub as well as don't need to alter the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist must comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is separate the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of eliminating the existing faucets can be fairly troublesome because of the limited accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washers are in area between the faucet and the sink. Protect the faucet in place with the supplier offered backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The previous type ought to be attached to the faucet ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Using the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub up until the spirit level reviews level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water system and inspect all joints and brand-new pipework for leaks and also tighten them if necessary. Load the bathtub as well as additionally examine the overflow outlet and also the regular outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has been utilized at the very least when as this will settle it right into its last setting.
Planning for the Installation
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to prevent pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to crack a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to always load the bath tub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealer can break fairly very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very drawn to How to Install a Bathtub and I really hope you liked the article. Please set aside a second to distribute this write-up if you enjoyed reading it. Thank you for your time. Kindly check our site back soon.
At This Website Report this page